Additional CCM coding and configurations with VDS Pro
- Thread starter madelgado
- Start date
graeme86
Veteran Member
To recode the CAN gateway just go into channel -19- in vcds.
Then just reenter the same code again and it will re-establish the CAN network and include the new CCM.
I think this is your problem.
The new CCM is not recognised in the CAN network.
Then just reenter the same code again and it will re-establish the CAN network and include the new CCM.
I think this is your problem.
The new CCM is not recognised in the CAN network.
Hello,
Many thanks for your help. Later today, I will do that and report back to you.
In the meantime, let me ask you about othe doubt related with the same problem. When I get the new CCM installed I do need to configure/onboard the new keys (that I already have) to this module in order to use the rc functionality. However I do need to get the new keys configured in the IMMO. The easy way is to move the old IMMO from old key to the new one, but I'd like to keep also the old working but need the SKC and this is the point. Uisng the VCDS I know that is impossible to get it from ECU but I do have a vagtacho (k + can) but can't get the SCK using it. Any clue?
Thanks for your great help
Cheers
Many thanks for your help. Later today, I will do that and report back to you.
In the meantime, let me ask you about othe doubt related with the same problem. When I get the new CCM installed I do need to configure/onboard the new keys (that I already have) to this module in order to use the rc functionality. However I do need to get the new keys configured in the IMMO. The easy way is to move the old IMMO from old key to the new one, but I'd like to keep also the old working but need the SKC and this is the point. Uisng the VCDS I know that is impossible to get it from ECU but I do have a vagtacho (k + can) but can't get the SCK using it. Any clue?
Thanks for your great help
Cheers
graeme86
Veteran Member
Match key fob to new CCM:
https://www.ross-tech.com/vag-com/cars/vw-remote-matching.html
https://www.ross-tech.com/vag-com/cars/vw-remote-matching.html
graeme86
Veteran Member
These instructions will synchronise the remote to the CCM, which is independent to the SKC in the cluster and the key IMMO chip.
Hello,
I've tried to connect the module using your notes and works but couldn't match the keys using the guidelines from https://www.ross-tech.com/vag-com/cars/vw-remote-matching.html
I did the procedure several times and got the same.
I've tried the connect the ccm 1c0959779F and follow the same procedure (to check if the problem was on the 1C0959799B module) but couldn't get it connected. Then I reenter the CAN code and after that I couldn't connect anymore to any module
Doing a full scan, it doesn't detect module now. If i click on 19 or 46 for instance it doesn't reply with any error, simply doesn't connect.
Did I damage anything? May I have reentered a wrong code on the CAN Gateway?
Any Procedure to recover, please?
Thanks a lot
Cheers
I've tried to connect the module using your notes and works but couldn't match the keys using the guidelines from https://www.ross-tech.com/vag-com/cars/vw-remote-matching.html
I did the procedure several times and got the same.
I've tried the connect the ccm 1c0959779F and follow the same procedure (to check if the problem was on the 1C0959799B module) but couldn't get it connected. Then I reenter the CAN code and after that I couldn't connect anymore to any module
Doing a full scan, it doesn't detect module now. If i click on 19 or 46 for instance it doesn't reply with any error, simply doesn't connect.
Did I damage anything? May I have reentered a wrong code on the CAN Gateway?
Any Procedure to recover, please?
Thanks a lot
Cheers
graeme86
Veteran Member
Low battery voltage?
Hello,
During the weekend I checked the voltage on pin 16 against the chassi and got 12.2v but seemed not very stable. I have checked also the pin 7 and got 4.5v but in fact I’ve got an warning stating no 12v power supply from ODB connector but I didn’t loose any function on any module. Am searching for any issue on the cabling/module. Any clue where to check please?
Thanks
Cheers
During the weekend I checked the voltage on pin 16 against the chassi and got 12.2v but seemed not very stable. I have checked also the pin 7 and got 4.5v but in fact I’ve got an warning stating no 12v power supply from ODB connector but I didn’t loose any function on any module. Am searching for any issue on the cabling/module. Any clue where to check please?
Thanks
Cheers
P2B
Top Post Dawg
Rather than responding to spam, just click Report instead.
Limitedblack
Member
Does anyone have a working “stock” list of settings for a 1C0 CCM in a RHD (UK), 5 door MK4 Golf with interior monitoring? Read a few lists, but seems contradictory.
Figured I should ask here because it is CCM related but do the door modules need to have the same color code as each other and the ccm? 3 of my 4 doors are 6Y, 1 is 6W and the CCM is 6W.... Which should be 6Y but someone put a sedan CCM in a wagon before I owned it. Everything seems to be working except for the rear hatch lock/logic.... just want to make sure.
It is best to look for a Golf with the exact same equipment as the one you are interested in, copy it and transfer it to the CCM of your Golf. I honestly use Vag Can Pro for these clones, it works perfectly and very quickly