RexNICO
Veteran Member
This popped up Thursday morning while ~150 miles from home and the wipers would not work. Turned a 2 hours drive into a very long drive waiting out the storms.
The error message might be windshield wiper defective (putting both in the post to help future searches).
Below is the 09-Cent. Elect. snippet from a complete Auto Scan. I did go into 09-Cent. Elect., cleared the DTC and it comes back instantly.
Most of my googling returns others with the error, but those posts report functioning wipers, while ours are not.
Before we got home to the scanner, we tried
Cycle car (several times, not change)
Hand movement of the wiper arms to see if they were jammed - no resistance, but did not move them very far (2-3 inches measured at the center of the wiper blade)
Opening/closing hood (read Q7 wipers will not operate with open hood) - no change and instrument cluster does not indicate hood open when it is closed.
Any help would be greatly appreciated.
Thanks
=======================================================================
Address 09: Cent. Elect. Labels: 4F0-910-279.lbl
Part No SW: 4F0 910 279 AG HW: 4F0 907 279 C
Component: ILM Fahrer H29 0390
Revision: 00000000 Serial number: 4F0907279
Coding: 0139123
Shop #: WSC 31414 790 00001
VCID: 6E8533FC7C97FD2B2D3-803A
Subsystem 2 - Part No: 8K0 910 557 Labels: 8K0-955-559.CLB
Component: REGENLICHTSENSORH04 0003
Coding: 00150059
Shop #: WSC 31414
Subsystem 3 - Component: Fehler Lin-Slave 01
1 Fault Found:
00908 - Control Module for Wiper Motor
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 81
Mileage: 262136 km
Time Indication: 0
Date: 2022.09.03
Time: 10:45:00
=======================================================================
The error message might be windshield wiper defective (putting both in the post to help future searches).
Below is the 09-Cent. Elect. snippet from a complete Auto Scan. I did go into 09-Cent. Elect., cleared the DTC and it comes back instantly.
Most of my googling returns others with the error, but those posts report functioning wipers, while ours are not.
Before we got home to the scanner, we tried
Cycle car (several times, not change)
Hand movement of the wiper arms to see if they were jammed - no resistance, but did not move them very far (2-3 inches measured at the center of the wiper blade)
Opening/closing hood (read Q7 wipers will not operate with open hood) - no change and instrument cluster does not indicate hood open when it is closed.
Any help would be greatly appreciated.
Thanks
=======================================================================
Address 09: Cent. Elect. Labels: 4F0-910-279.lbl
Part No SW: 4F0 910 279 AG HW: 4F0 907 279 C
Component: ILM Fahrer H29 0390
Revision: 00000000 Serial number: 4F0907279
Coding: 0139123
Shop #: WSC 31414 790 00001
VCID: 6E8533FC7C97FD2B2D3-803A
Subsystem 2 - Part No: 8K0 910 557 Labels: 8K0-955-559.CLB
Component: REGENLICHTSENSORH04 0003
Coding: 00150059
Shop #: WSC 31414
Subsystem 3 - Component: Fehler Lin-Slave 01
1 Fault Found:
00908 - Control Module for Wiper Motor
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 81
Mileage: 262136 km
Time Indication: 0
Date: 2022.09.03
Time: 10:45:00
=======================================================================