Search results

  1. mur3633

    1.9 ASZ to 2.0 BKD.

    Broken tooth on crankshaft 🙄
  2. mur3633

    1.9 ASZ to 2.0 BKD.

    I completed AJM block with 2.0 TDI 8V pistons and PD130/150 internals. Also I put SDI camshaft from 2.0 PD SDI engine. When I try to crank, it throws P0321 Engine speed sensor G28 - implausible signal, which is Crankshaft sensor related. It is old type sensor with hole in engine block. Timing is...
  3. mur3633

    PD TDI valves - Which brand?

    Hi, I want to buy new valves. Which brand is the best? Mahle, TRW or something else?
  4. mur3633

    TDI 110hp AFN: 00575 Intake manifold pressure

    Hello, I have problem. Car is Passat TDI AFN 110hp. It goes to safe mode and throws fault code 00575 Intake Manifold Pressure 17-00 Control Difference What can cause this? EGR is blocked, new vacuum hoses, new N75, new MAF and MAP sensors, turbo was cleaned two times, VNT mechanism doesn't block.
  5. mur3633

    1.9 ASZ to 2.0 BKD.

    I want to bore out AJM block to 2.0? I will use pistons from 2.0 TDI 8V BMM engine. But what about connecting rods, crankshaft and bearings? Can AJM crankshaft stay? Which conrod bearings should I use 1.9 or 2.0?
  6. mur3633

    PD BIPs too high

    What can cause too high BIPs in measuring block 023 (VCDS)? I'm getting from +90 to +120ms for all four injectors. Is there any way to solve this or I need another injectors? Measuring block 013 is good, every four injectors are about 0.0. 115hp AJM engine, everything stock. Car starts very...
  7. mur3633

    2005 BEW PD lift pump operation and internals

    Another 1J0 919 050 (no suffix) VDO pump, drops 2L per minute on hose just before fuel filter. Cleaned pump internals as much as I could. Is it ok or it must go over 3L per minute? In the first post it is written for 1J0 919 050 B pump, which is a little bit different... Can anyone confirm?
  8. mur3633

    MFD G to D - downgrade

    Could MFD G be downgraded to D firmware to enable 3LB connection? Anyone done that?
  9. mur3633

    2005 BEW PD lift pump operation and internals

    Yeah, it was faulty lift pump...
  10. mur3633

    kw1281test: A Free VDS-Pro / VagTacho Alternative

    Thank you for this bro!🍺 Remote windows activated with brand new Acer Win10 laptop, VAG Commander 1.4 Chinese cable and 1J0 CCM in Mk4 Golf MY2001
  11. mur3633

    2005 BEW PD lift pump operation and internals

    I read the whole topic, this is excellent! My pump is 1J0 919 050 VDO from 2000. On ignition I got about 50cc, while at 12V, 2 Litres per minute. Cleaned screen, it was dirty, now getting 2.2 Liters. Is it bad lift pump? Also can I take motor from petrol lift pump? Is it same as diesel? Not...
  12. mur3633

    PD115 hard cold start

    In tank pump works. No air leaks, everything is ok Bought another tandem pump to try. I think this is something fuel related. Fuel is somehow returns back, so it has air in fuel system. Thank you for help, I will write what is problem if I fix. [emoji481]
  13. mur3633

    MK4 4motion ATD > ASZ or ARL

    Also don't forget PD150 headbolts.
  14. mur3633

    PD115 hard cold start

    Anyone? This video is before repaired head with injector seats. Now it is much better, but if car stays for 2 days, then I have this problem. Tandem pump again? I have also bad low end. When I press accelator pedal, car stays for 1-2 seconds, then boost kicks in very agressive after 2000rpm...
  15. mur3633

    Anyone used Liqui Moly 4100 5w40 oil

    75W is right viscosity. 2.3 liters.
  16. mur3633

    Engine oil

    Liqui has great products.
  17. mur3633

    Anyone used Liqui Moly 4100 5w40 oil

    G 052 171 a2.
  18. mur3633

    PD115 hard cold start

    VCDS showing 0.0/0.5 on Torsion value.
  19. mur3633

    PD115 hard cold start

    Since last year my Golf started very hard on cold start. Changed almost everything. Tandem pump, vacuum hoses, crankshaft sensor, camshaft sensor, N75, glow plugs, done cylinder head completly with injector seats, new injector seals, repaired turbo, repaired injectors, new injector loom, etc...
  20. mur3633

    Anyone used Liqui Moly 4100 5w40 oil

    TT 4100 is excellent oil.
Top