Search results

After checking my bank statement, I also found that they had overcharged my card by almost 14.00 over the invoice/receipt they had send to me. I go no response from them, so I had to "dispute the charge" with my CC company. I won't do business or recommend anyone else buy from them.

This the one ? https://www.fcpeuro.com/products/audi-vw-vcds-diagnostic-interface-ross-tech-vchv23

Well, I'll do an update on my ecm issue. Car is still running fine after changing it out with the junk yard unit that Kerma re-programmed. Before I changed it, I had ordered a Ross Tech VCDS. They charged 199.00 for the unit and 36.77 for fedex ground shipping. Not knowing how big or heavy the...

Doright, I would quit messing around, call Kerma and send them your ecm's.

Yes, the used ecm has to be sent along with the original one. They will clone the used one based off of the original one. I just went thru all this with Charlie at Kerma TDI. https://kermatdi.com/ Car started right up and runs great. Sent out the original one the first time to Module Experts...

Here is an update on my 2006 TDI Jetta no start issue. Sent the original ecm to Module Experts in Jacksonville Fl. They tested the module-took it apart and reported it as not repairable. Wanted 600.00+ for one to go. I have a feeling they are third party vendors as I could not take the...

where do you get it (the used ecm) programmed to the cars VIN # ?

yes

I ordered a Ross Tech VCDS scanner cable and will use my laptop with their program. Checked into renting one but being as I am going to keep the car (wife loves it and drives it most of the time) and know I will be changing the clutch and cam in the future, decided just to buy the scanner. I...

Thanks, I found the ECU removable procedure in the VW maintenance manual. I was just about to pull the wiper arms when I had to go to my office and while there check the forum. I did find a youtube video concerning a 2007 Jetta (gas) no start issue and viewed it. That is the exact same issue I...

How do you access the ecm on this model? Also notice you are on the 3rd camshaft. I'm guessing I will have to change this one out before long as well as the clutch.

New starter spins the motor over very fast. Not a peep from the motor.

https://1drv.ms/u/s!AlqXTowCsi4Uh-8g2K3ZGxw5Bxwuyw snap shot of dash with key turned on----

I'm looking into renting a VCDS but have some doubts about the communication network on the car or the lack of it, maybe bad relay/wiring or? If it is a sudden wiring issue, would any type of scan guage be able to communicate with the ECM? I made sure the Autel was updated and tried it again...

Not being smart, but what is a "proper" scan tool? I have used the Autel on several cars including this one, over the last two years with no issues until now. I will check the battery connections now. Starting to get some of the hurricane effects here as it moves inland.

This Jetta was running great, until this morning. Just read thru cochrank's posts and my 2006 (167,000) has some of the same issues but some different, so I thought I would put this on a separate thread. Just this week when starting the car, it would start and run but I would hear a noise for a...

Looked for several hours and can't seem to find the procedure for removing the intake manifold off our 2006 Jetta. Want to do an intake and system cleaning. The VW maintenance manual is no help. Anyone have a link to the procedure?

Checking to see what the fix will be for this engine code. Thanks ahead of time for the help!!

I have a 2006 Jetta TDI with 159,000 miles and the water pump has started leaking. I changed the original timing belt and water pump at 98,000 miles with a Gates kit. I am considering have someone do a through service to it including timing belt/water pump, intake cleaning' new clutch and...

Thanks Rx ! #3 cam ? how many miles on your 2006? Which replacement cams have you used?