Recent content by tripl-e

  1. T

    Help With Diagnosing Electrical/Instrument Panel Problem

    Many useful comments here re: cluster repair but the root cause of your failure appears to be the fan/harness incident. A short circuit there (an improper connection of an unfused +12V wire with a direct ground path) has heated both the positive wire and its ground path co-conspiritor wire...
  2. T

    B4 Third Brake Light.....?

    Plug the third brake light assembly into it's connector (where you observed 11.7 V with no load) and measure the voltage with the load applied. If the circuit provides 12V with no load but does not with a load applied then resistance in the supply side of the circuit is likely. If the 12V is...
  3. T

    trip meter resets on cold start?

    I had a similar over temp failure of a capacitor in my BMW touring. I'd have no tach/speedo when the cabin got summertime hot. I don't see why the VW panel couldn't fail in a similar fashion.
  4. T

    B4V brake help needed.... (ABS - GLX TDI coversion) LF caliper

    You can separate mechanical and hydraulic causes by opening the sticking caliper's bleed fitting when the brake is stuck. If trapped hydraulic fluid is the problem the caliper will relax, if mechanical drag is the issue it probably won't.
  5. T

    Removing pins from connector

    There are specific removal tools available for most automotive connectors but you seem to be on the right track in your picture. When I made my tools I used a piece of plain wire, hammered the end flat to thin it slightly then filed it to width. I wound up with an essentially rectangular cross...
  6. T

    How long do I have?

    This bring to mind the timeless, "If it ain't broke, don't fix it!" The turbo will give you plenty of notice that it's nearing the end of its service life. Till then, as Abacus suggests, drive it.
  7. T

    Replaced Broken Trans, Now Clutch Slips

    The high clutch pedal is key! Something is amiss in the release hardware, the pressure plate is not applying full clamping force to the disc. Somehow the throwout bearing and the release arm are not able to retract fully. Try opening the bleed nipple on the slave cylinder to see if hydraulic...
  8. T

    96 Passat Wagon

    Yes, lots of interest. PM sent.
  9. T

    Another 97 passat B4 no start

    Easy enough to check for +12V from ign. switch to solenoid when no-start condition exists. The solenoid does two things; it mechanically engages the motor's bendix drive with the flywheel and, at the end of that engagement stroke, it closes the high amperage switch which energizes the starter...
  10. T

    What do you think of this lifter wear?

    Exhaust or Intake lifter more damaged?
  11. T

    New TDI Owner

    My '97 1Z Passat has an EGR cooler so at least some '97s are so equipped. EEE
  12. T

    random "dead" battery - no start

    Look at the voltage being supplied to the starter solenoid thru your 'bypass' circuit and switch. Any combination of factors (weak battery, poor terminals, voltage loss thru bypass wiring) could lower the voltage to a critical level. What that level is exactly will vary with the condition of...
  13. T

    1998 TDI no start after Timing Belt and Water Pump!!

    1.Check the flywheel timing mark AFTER the belt tensioner is set. Often the act of tensioning the timing belt will move the engine slightly and create a timing error. 2. You say you used 'flat metal' and feeler gauge(s) to locate the camshaft. The locating slot in the cam is offset so the...
  14. T

    B4 sedan trunk lid liner help needed

    http://vagpart.com/vw/passat-pa-us-1997-86780-luggage-compartment-trim/ I think you're looking for #10 Grommet, it receives the plastic tabs attached to the trim piece. The drawing shows an 'expanding rivet' to attach the rear edge of the lining to the lid but mine has 4 sheet metal screws...
  15. T

    Putting the B4v's issues' history on one thread

    You need to be logging data with VCDS when the symptom presents itself. This could be happening almost anywhere, frayed wires in the IP harness, blockage in the fuel delivery plumbing (less likely in my opinion), ignition switch gremlins, quantity adjuster inside the IP, just about anywhere an...
Top