Swirl flaps

Lavek6

Active member
Joined
Jun 15, 2017
Location
Croatia
TDI
Golf IV Golf VI
Golf mk6 2.0 tdi 103kw 180k km
When i start car p2004 i delete code and it is fine for that day or maybe one more time if i drive a lot and start a car few more times , the leaver is moving free, how can i test motor should it move lever on idle at some rpm?, also leaver a bit worn on outside like it was rubing against motor but when moving it myself could´t sea how could it reach motor.
 
Last edited:

D-Cup

Veteran Member
Joined
Jul 22, 2017
Location
San Antonio TX
TDI
2010 Jetta TDI Cup Edition, 2003 Jetta GLS, 2000 Jetta GLS, 2012 JSW
Dieselgeek bracket for fix.
There’s a thread on here about it. Code should clear itself within a few drive cycles once installed. Hopefully shipping isn’t an issue.
Dieselgeek.com
 

ksing44

Veteran Member
Joined
Feb 13, 2010
Location
Southeast PA
TDI
2010 Golf TDI
If your car had the fix, a new intake manifold will be covered by the warranty. I got a new one and I'm not alone in having that experience.
 

Lavek6

Active member
Joined
Jun 15, 2017
Location
Croatia
TDI
Golf IV Golf VI
Dieselgeek bracket for fix.
There’s a thread on here about it. Code should clear itself within a few drive cycles once installed. Hopefully shipping isn’t an issue.
Dieselgeek.com
Yes i was thinking about that, but just wanted to sea if there is some test to do first, also i writed the wrong code i get Code P2004 Intake Manifold Runner Control Stuck Open Bank 1
 

ksing44

Veteran Member
Joined
Feb 13, 2010
Location
Southeast PA
TDI
2010 Golf TDI
How could there be warranty after 10 years?
My car is 9.5 years old and I got a new one under the extended warranty that came with the fix, but I didn't see that you're from Croatia. Maybe you didn't get that in Croatia like we did in the US.
 

Henrick

Top Post Dawg
Joined
Aug 24, 2010
Location
Ireland
TDI
Golf VI TDI, 77 kW (CAYC)
Golf mk6 2.0 tdi 103kw 180k km
When i start car p2006 i delete code and it is fine for that day or maybe one more time if i drive a lot and start a car few more times , the leaver is moving free, how can i test motor should it move lever on idle at some rpm?, also leaver a bit worn on outside like it was rubing against motor but when moving it myself could´t sea how could it reach motor.
This can be fixed using a special bracket. Here it costs 30 Euros. If you need one, just drop me a PM, I'll be happy to buy it for you and ship.
 

Lavek6

Active member
Joined
Jun 15, 2017
Location
Croatia
TDI
Golf IV Golf VI
Ty i will see :). , also not to open new thread one more question, i installed cruise control switch and activated it with auto-com , i get as soon as i start driving !and cruise control sight near ! and cruise is not working, i did't look at module number but i assumed it is good since i have MF steeing wheel?
What could it be except brake and clutch peadal switch?
 

Lavek6

Active member
Joined
Jun 15, 2017
Location
Croatia
TDI
Golf IV Golf VI
This can be fixed using a special bracket. Here it costs 30 Euros. If you need one, just drop me a PM, I'll be happy to buy it for you and ship.
I instaled bracket tested pins 1,3 are 5v 4 is 12v and 5 is 12v, motor is working when i test it, position sensor is working from about 0.75v to almost 4v on pin 2 whe i move the leaver, what is controling this motor, now even if i clear the code, it is permanent but mil is after 2,3 startup showing up.
If i understood evrything it should work now but leaver is not moving at startup and idle or when i press the acc. pedal
 
Top