dzcad90
Rolex & gin
I'm not 100% sure, I've only done this on the Jetta Sedan. I know it's in the headliner. I thought I read in the wagon it's above the left rear door area and in the golf hatch it's near the location that you stated above.
Are you sure about that coding?Broncosaurs said:I got a new 9W3 "D" bluetooth module, installed it and recoded with the following:
9W3.Telephone 77...0013077
When you go from 9W2 to 9W3, you not only have to code the telephone module, you have to code the MFSW to use the phone button as a mute button. This would cause the MFSW to operate the BT module incorrectlyh, however I don't see it disconnecting the BT connection between phone and module. Did you install the BT antenna on the BT module? What kind of phones are you using?Broncosaurs said:Hi, all. I have a 2010 Sportwagon with the factory RNS510. The car came with the lack luster bluetooth (9W2) so I did not have phone control with the radio touch screen. I got a new 9W3 "D" bluetooth module, installed it and recoded with the following:
9W3.Telephone 77...0013077
Nav 37....000004000400002000
The phone links up and all functions for the phone show up on the nav system. Yah..
BUT, after 4 minutes the radio/nav disconnects with the phone and I get a message stating this. Does anyone have an idea on what would cause the phone to disconnect? Not the phone, the phone worked well with the old bluetooth and I also tried the wife's phone with the same results. Also I lost the compass direction in the MFD that was next to the time on the top and I can't change the radio channels with the steering wheel buttons any more. Thanks for any help.
Brad
In regards to cars that came with the Aux input... My Passat has that same Aux hook up and I just upgraded the radio to an RCD 510. Do you know if the RCD 510 and RNS 510 use the same pin assignments for this? I also installed an MDI iPod unit and the RCD 510 doesn't seem to recognize it or let me recode it. iPod connects though which is the odd part.17. If your car was equipped with the Aux In connector in the center console, you must do some pin swapping on the BLUE connector in the electrical harness. These steps are covered here.
The large black connector actually houses three smaller connectors. You will be removing the blue connector from the black connector. Use a small screwdriver to push the clip down on the blue connector and pull it from the black connector. One side of the blue connector is open so you can see the black housing inside of it. On the side of the blue connector you can see a little spot to pry and the blue housing will slide off of the black connector.
In the above picture, you can see that the Aux wiring is a separate wire bundle from the rest of the car. It contains a lime green wire, a gray wire, and a yellow wire. We will be moving the yellow and gray wires.
Using the smallest straight screwdriver you have (I used a 1.4mm driver), push down on the barb of the gray wire and push it toward the rear of the connector. After you reach a ceratin point, you can then gently pull the wire out from the connector.
If you look at the top of the black connector, you can see that each wire position is numbered, 1-6 on the top and this continues on to the bottom from 7-12.
You will swap the gray wire to pin 7 and the yellow wire to pin 1.
Re-assemble the black connector into the blue connector and then re-assemble the blue connector into the larger connector housing that connects to the radio.
I don't have any answers for you but I also have a 2012 and I'm wanting the unit with NAV. I've already got the double din unit in my car just didn't get the NAV. I've got Sirius and iPhone connection along with blue tooth. Not sure what the model is on the unit. I am definatily wanting the factory NAV put in. Just not sure what all intails on getting it to work. Will there be some code problems if I were to swap mine out with a NAV unit? Should I already have the antenna for NAV or would I need to install one?recently I purchased a RNS-510 i installed it, not that it was much of an install jus plug n play type of deal, but when i connected it i punched in the code and it turned ON fine but there was no sound???? the GPS is working everything comes on fine jus no SOUNDno hissing no nothing. Is there something i need to do to get this thing to work like press a few buttons or something??? Anyways any help would be greatly appreciated.... THANKS in ADVANCE....
p.s. i have a jetta tdi 2012
The physical process for removing (or replacing) the radio in any Mk5 is exactly the same. However, what the coding needs to be changed to depends entirely on what you intend to replace your RNS-510 with.Is the process reversed for removing the RNS-510? I hate mine and would gladly sell it.