www.tdiclub.com

Economy - Longevity - Performance
The #1 Source of TDI Information on the Web!
Forums Articles Links Meets
Orders TDI Club Cards TDIFest 2016 Gone, but not forgotten VAG-Com List Unit Conversions TDIClub Chat Thank You

Order your TDIClub merchandise and help support TDIClub


Go Back   TDIClub Forums > TDI Model Specific Discussions Areas > VW MKV-A5 Golf/Jettas

VW MKV-A5 Golf/Jettas Discussions area for A5/MkV Jetta/Golf (2005/2006 PD and 2009 CR).

Reply
 
Thread Tools
Old December 18th, 2019, 14:23   #1
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default HELP! P0341 Cam sensor Implausible Signal

Update I need help with PO341 Camshaft Position Sensor (G40): Implausible Signal. I have replaced the cam sensor with 2 different ones now( both brand new), traced down all the wires nothing (broken or damaged), checked and cleaned all the grounds ,tested the wires at the sensor , even replaced the ECU. The timing is on at the cam also. I'm completely out of ideas and I'm trying to see if anyone else has experienced this before. Thank you


Hello, i have a 2005.5 MKV Jetta TDI
i need to retrieve the SKC or ( PIN ) i have vag tacho 5 but cannot get that to work for me.
What program or tool do you guys use to retrieve the SKC
Thanks

Last edited by srt-kapp; December 22nd, 2019 at 10:29.
srt-kapp is offline   Reply With Quote
Old December 18th, 2019, 14:37   #2
mr.loops
Veteran Member
 
Join Date: Nov 2010
Location: Kelowna
Default

Vag tacho or the dealer

It should work...Did you buy a Chinese knockoff?


Sent from my iPhone using Tapatalk
mr.loops is offline   Reply With Quote
Old December 18th, 2019, 14:40   #3
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default

No i have a real version of Vag tacho 5. I saw there is another tool called Super Vag Plus but i'm not sure if that will work for the CAN vehicles
srt-kapp is offline   Reply With Quote
Old December 18th, 2019, 14:43   #4
mr.loops
Veteran Member
 
Join Date: Nov 2010
Location: Kelowna
Default

Hmm
Any fault codes- ie: no comms with modules?


Sent from my iPhone using Tapatalk
mr.loops is offline   Reply With Quote
Old December 18th, 2019, 15:03   #5
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default

I have a cam sensor code p0341 but that only comes on when the vehicle is running. I have power to the connector and ground. i've even replaced the sensor twice I checked all the grounds and even went and traced the whole harness down looking for a break. The timing is right at cam. I truly believe the ECU is bad
srt-kapp is offline   Reply With Quote
Old December 18th, 2019, 15:06   #6
mr.loops
Veteran Member
 
Join Date: Nov 2010
Location: Kelowna
Default HELP! Retrieve SKC

If you donít see a reference signal on any of your sensors ( key in the on position) this could confirm a bad ECU


Sent from my iPhone using Tapatalk
mr.loops is offline   Reply With Quote
Old December 18th, 2019, 15:16   #7
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default

The CEL does illuminate Key on engine off but does not come on when running/driving. That's kinda what tipped me off to think the ECU is Bad. I have a used ECU all ready to go but need the SKC from the original part so i can transfer the new used one over
srt-kapp is offline   Reply With Quote
Old December 18th, 2019, 16:54   #8
1854sailor
Resident Curmudgeon
 
1854sailor's Avatar
 
Join Date: Aug 2004
Location: Baltimore, MD
Default

I don't think that VAG Tacho will work on a 2005.5. Dealer, or find a tuner who can do an immo delete.
__________________
Never wrestle with pigs. You both get dirty and the pig likes it.
-George Bernard Shaw
1854sailor is offline   Reply With Quote
Old December 19th, 2019, 08:33   #9
mr.loops
Veteran Member
 
Join Date: Nov 2010
Location: Kelowna
Default

Quote:
Originally Posted by 1854sailor View Post
I don't think that VAG Tacho will work on a 2005.5. Dealer, or find a tuner who can do an immo delete.
it should... MY 2003-2007 : http://www.maltchev.com/kiti/guide.htm

OP, you might have missed a step, or did not have the correct dash selected on the drop down menu.


Switch ON ignition with the new key. Be sure that the type of transponder key is correct, use TP23 for VW, TP25 for Audi, TP22 for Seat, TP24 for Skoda! Start software, select "VDO NEW - CAN bus" from menu. Press "Connect Selected ECU" button, after 5 seconds the data of the dash will be shown on screen. Press "Program New Key", software will open a new window. See the picture.
Unsupported dash? Click here for Help!

Check "Erase all old keys" if you wish. In this case all keys will be erased. If you left this unchecked, the new key will be added to the existing keys. No need to program all available keys again. Press "Continue" , the new key will be programmed in 5 seconds. Wait while the immobiliser's warning lamp is turned off. Turn off/on ignition, and start engine. If the immobiliser's warning lamp starts flashing faster, this means that the type of the transponder key is not correct, or this key is already programmed to the car! Do NOT repeat the programming procedure if immobiliser's warning lamp is flashing faster! Just switch ON ignition with right type TP2x transponder key! If you want to program more than one new key, repeat again the same procedure from the beginning for every next key.



According to the website, there are some dashes that are unsupported (you'll see a "Seed key-OK" warning) Unlucky, if this is you
mr.loops is offline   Reply With Quote
Old December 19th, 2019, 14:42   #10
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default

I'll have to look at that again and give that a try. I did purchase Super Vag K+CAN so hopefully that will work for me
srt-kapp is offline   Reply With Quote
Old December 20th, 2019, 06:56   #11
pdq import repair
Veteran Member
 
Join Date: Nov 2016
Location: idaho
TDI(s): 09 Jetta
Fuel Economy: 38.5
Default

If that doesn't work, call the independents and locksmiths. If they have the Autel IM608 they can direct read the ecu pins if you carry them in. Or OBD read the existing one in the car if needed.

you will need both SKC's if you have to use VCDS, which you sometime do.
pdq import repair is offline   Reply With Quote
Old December 21st, 2019, 11:21   #12
srt-kapp
Member
 
Join Date: Jan 2010
Location: Germantown OH
Default

I successfully used Super Vag to retrieve the pin and adatped the used ECU to my car. Unfortunately that did not fix my running concern. I still have the
6725/P0341/000833 - Camshaft Position Sensor (G40): Implausible Signal


The CEL still does not illuminate when running. You can unplug multiple sensor trying to trigger the light and still no success. I feel like i still have a wiring issue. When it starts it starts easy there is just an extended crank. Also it runs well with no smoke from unburnt fuel or timing being off. I'm at a loss right now on this car and not sure what to do next
srt-kapp is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Key PIN retrieve redneckpunk OBD Scanners 8 May 8th, 2016 18:31
Bricked EDC15p+ can't retrieve SKC 00johnson VW MKIV-A4 TDIs (VE and PD) 0 May 10th, 2014 06:26
Radio codes: Can you retrieve them before you need them? Turbine Suburban VW MKV-A5 Golf/Jettas 11 September 1st, 2009 19:44
Vag-Tacho on 2000 Beetle to retrieve SKC marspball TDI 101 20 August 15th, 2009 19:54
OBD Code - way to retrieve without a device? RedeyeTDI OBD Scanners 3 April 7th, 2007 07:07


All times are GMT -7. The time now is 01:11.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright - TDIClub Online LTD - 2017
Contact Us | Privacy Statement | Forum Rules | Disclaimer
TDIClub Online Ltd (TDIClub.com) is not affiliated with the VWoA or VWAG and is supported by contributions from viewers like you.
© 1996 - 2017, All Rights Reserved
Page generated in 0.15857 seconds with 13 queries
[Output: 104.15 Kb. compressed to 87.70 Kb. by saving 16.45 Kb. (15.79%)]