sleze
Veteran Member
I am trying to increase my idle speed from 860ish to 900 in order to get rid of an annoying rattle. I tried following the instructions from Ross Tech's website:
When I tried it, I got a security access required in the fields(no rpm, etc.). I started fiddling around (I used the login code that Jeff gave me when I got RC2 but that didn't work in the security button)and turn the car off and turned the ignition so the engine wasn't on but the computer was. I went back in and saw the rpm(0) as well as a couple other fields including the value of the adaptation, 0. I then turned the car on and the RPM went to 861 and the adaptation number stayed at 0. I put in 124 and it accepted it but nothing changed. I closed out and went back in and alluva sudden the value was 134. I changed it to 132 and it accepted but nothing changed.
I closed out of adaptation, turned the car off/on and went back in. Once again I got the security error. I then decided to run an autoscan and it threw the following code:
Address 01: Engine
Part No SW: 038 906 016 R HW: 028 101 198 2
Component: R4 2,0L EDC G000AG 6416
Coding: 0150034
Shop #: WSC 05314
1 Fault Found:
16683 - Boost Pressure Regulation: Control Range Not Reached
P0299 - 000 - -
Freeze Frame:
RPM: 2205 /min
Torque: 256.0 Nm
Speed: 59.0 km/h
Load: 52.9 %
Voltage: 14.21 V
Bin. Bits: 00101000
Absolute Pres.: 2468.4 mbar
Absolute Pres.: 1968.6 mbar
Readiness: 0 0 0 0 0
Question 1 - How do I set my idle speed without that security code?
Question 2 - Does the code thrown(I don't have a CEL) have something to do with my idle rattle?
Idle Speed Adaptation (see your Repair Manual):
With engine warmed up, at idle:
[Select]
[01 engine]
[Adaptation - 10]
Enter channel 01
Enter an adaptation value between 124 and 132
[Save]
With engine warmed up, at idle:
[Select]
[01 engine]
[Adaptation - 10]
Enter channel 01
Enter an adaptation value between 124 and 132
[Save]
When I tried it, I got a security access required in the fields(no rpm, etc.). I started fiddling around (I used the login code that Jeff gave me when I got RC2 but that didn't work in the security button)and turn the car off and turned the ignition so the engine wasn't on but the computer was. I went back in and saw the rpm(0) as well as a couple other fields including the value of the adaptation, 0. I then turned the car on and the RPM went to 861 and the adaptation number stayed at 0. I put in 124 and it accepted it but nothing changed. I closed out and went back in and alluva sudden the value was 134. I changed it to 132 and it accepted but nothing changed.
I closed out of adaptation, turned the car off/on and went back in. Once again I got the security error. I then decided to run an autoscan and it threw the following code:
Address 01: Engine
Part No SW: 038 906 016 R HW: 028 101 198 2
Component: R4 2,0L EDC G000AG 6416
Coding: 0150034
Shop #: WSC 05314
1 Fault Found:
16683 - Boost Pressure Regulation: Control Range Not Reached
P0299 - 000 - -
Freeze Frame:
RPM: 2205 /min
Torque: 256.0 Nm
Speed: 59.0 km/h
Load: 52.9 %
Voltage: 14.21 V
Bin. Bits: 00101000
Absolute Pres.: 2468.4 mbar
Absolute Pres.: 1968.6 mbar
Readiness: 0 0 0 0 0
Question 1 - How do I set my idle speed without that security code?
Question 2 - Does the code thrown(I don't have a CEL) have something to do with my idle rattle?